Behind the Tech

Aircraft availability is the new currency of maintenance, repair and overhaul (MRO)

Why operators now rank turnaround time (TAT) above price, and how MRO providers can make it predictable.

TABLE OF CONTENT

  1. TL;DR
  2. Turnaround time is decided between the tasks
  3. Four places where availability leaks
  4. From promised TAT to proven TAT
  5. See where your turnaround time goes
  6. Related articles

PUBLISHED: 3 November, 2026

UPDATED: 4 November, 2026

7 min read



asset management industrial manufacturing ground support equipment

TL;DR

• Availability beats price. In a panel poll at Aviation Week's MRO Europe 2026 conference, 74% of respondents prioritised turnaround time (TAT) over price (26%).

• Part of TAT is lost finding equipment. Before tracking, LOTAMS staff spent up to two hours a day searching for equipment, and Condor Technik crews drove routes of up to 10 km across Frankfurt Airport.

• Asset data makes TAT predictable. Tracking ground support equipment (GSE), tooling, material trolleys and transport fixtures gives MRO providers the data to protect TAT, and gives airlines evidence to contract on.

At MRO Europe 2026 in Amsterdam, the most telling number had nothing to do with AI or new capabilities. During a panel on maintenance for business aviation, low-cost carriers, leisure airlines and wet-lease operators, the audience was asked to choose between two priorities: turnaround time (TAT) or price. 74% chose turnaround time. Price got 26% (Aviation Week).

What is turnaround time (TAT) in MRO? TAT is the total elapsed time from the moment an asset, such as an aircraft, engine or component, arrives at an MRO facility until it has been serviced, inspected, repaired and released back to active service.

It was one room, not a market survey. On the panel, MRO providers stressed that operators competing for limited maintenance capacity want predictable delivery schedules. Every extra day on the ground means a disrupted schedule, wet-leased capacity or lost revenue. Panelists also pointed to longer-term agreements and closer relationships between operators and MRO providers.

So availability is the real currency. Part of it is won or lost in the movement of equipment, tooling and parts around the aircraft.

Turnaround time is decided between the tasks

TAT depends on labour, hangar slots and spare parts. It also depends on equipment being where the technician needs it. A technician waits for a tire-change cart. A crew drives across the airfield looking for a tow bar. A team calls around to find out which hangar has the jacks, or whether the transport fixture is back from the supplier.

None of these delays shows up as its own line in a P&L (profit and loss statement). They are booked as labour hours or waiting time. Because they vary from one check to the next, they make TAT harder to predict.

If operators are buying predictability, MRO providers need control over these delays. That starts with knowing where every piece of non-powered equipment is, and whether it is free.

Four places where availability leaks

1. Ground support equipment on the apron

At Frankfurt Airport, the Condor Technik hangar sits on the opposite side of the field from the terminals. The route around the runway can be up to 10 km, with a 30 km/h limit across the site. Teams lost time hauling ladders and tire-change carts on inefficient routes because nobody knew where the nearest unit was.

Condor Technik fitted its non-powered GSE with Sensolus trackers and was live within two days, with no infrastructure installed airside. Its project manager for process improvements, Vera Pomnitz, says many trips from one side of the airport to the other have now disappeared. Read the Condor Technik story.

2. Tooling and equipment in and around the hangar

LOTAMS, the Polish MRO at Warsaw Chopin Airport, runs more than 1,200 equipment units across a 100,000 m² apron and almost 20,000 m² of hangar space. At Chopin, an operation takes place roughly every four minutes. Before tracking, staff spent up to two hours a day searching for equipment.

With 600+ Sensolus trackers and zone markers inside the hangars, teams now find what they need in seconds from a phone. Alerts flag equipment that is idle too long, has an expired inspection or has left its zone. The location history also lets LOTAMS reconstruct who used what, and when, after an incident. Read the LOTAMS story.

3. Parts and materials moving through the shop

Availability and traceability are two sides of the same coin. A part you can’t locate is a part you can’t fit, and a regulator will want to know where it has been.

At Pratt & Whitney Canada, Sensolus trackers deployed by partner Gemba Systems follow the trolleys that carry materials across the Montreal shop floor. Locating them used to be manual. Now real-time location data supports traceability, audit readiness and just-in-time delivery across assembly sites. The same logic applies to rotables and components moving through a repair loop. Read the Pratt & Whitney Canada story.

4. Transport fixtures and returnable packaging

Aircraft components travel in jigs, racks and containers that are expensive, often custom-built and constantly in motion between sites. When one goes missing, a component waits.

Airbus, our first enterprise customer, tracks the jigs that carry airplane components through production across Europe and the UK. Misplaced tools are now located within minutes, and nearly 100% of asset journeys are recorded without gaps. Read the Airbus story.

The problem is the same outside aviation. Neovia Logistics saw about 40% of its returnable cages and totes vanish from the return cycle each year once they left with third-party carriers. GPS tracking eliminated £1.92m of contractual asset exposure (Neovia story).

From promised TAT to proven TAT

If turnaround time (TAT) is what customers buy, MRO providers that can prove a reliable TAT can compete on measurable value rather than price alone. That proof starts with data about the assets around the aircraft.

For MRO providers:

  • Measure the hidden minutes. Track search time, idle time and cross-site trips for GSE, tooling and fixtures, so you know which delays to tackle first.
  • Right-size instead of buying buffer stock. Utilisation data shows which equipment is overused and which sits idle. At Vaillant, the same data avoided around €30,000 of new cart purchases on a single project, with a return on investment (ROI) in about 1.2 years (Vaillant story).
  • Turn visibility into a sales argument. Location and usage history is evidence you can bring to a contract renewal.

For airlines and technical procurement:

  • Ask how TAT is protected, not only what it is. How does your MRO partner make sure tooling, GSE and fixtures are ready when the aircraft arrives?
  • Contract on predictability. An average TAT does not show how much individual checks vary. Ask for the data behind the promise.

See where your turnaround time goes

Sensolus trackers work indoors and outdoors with no airside infrastructure and run for up to 10 years on one battery. Condor Technik was live in two days. Want to know how many hours your teams spend searching for equipment, and what that does to your TAT? Book a demo and we'll show you with your own asset types.

Request demo

Related articles